Відео

Thank you for the video!

It's fixed but what was the root cause of the failure?

Sure is nice to see some green grass! We are really dry in Virginia!

Great job guys and thank you for the video 👍😎🇺🇸

I would like to get one of these for my Gravely ZT HD, but was wondering how difficult it is to remove this in the fall when I want to install my bagger system?

hello, great video, from Leesburg Virginia

Ok, That’s why you guys cover every inch of your skin, you’re afraid to get dirty. 😂 Enjoy the heat! That’s nuts. I’d be doing it naked if it were legal. Once you master the job you will see that you don’t have to work hard or get excessively dirty doing lawns. All the best!

This same video is on another channel called Mark's Work Shop. They appear to be stealing your content.

Nice work and good to see you guys mowing again. Thank you for the video 👍😎🇺🇸

Nice job!!! Love to do fields like that. Night and day difference when done!!!

Appreciate the video (watched the whole thing), but think I'd just get a little trailer.

You could set up the rear truss as a a hinge and thread your pull line around a pulley on it so once the canoue came forward and hit an end stop, it would raise the tail of the canoe so the canoe wnds up parallel to the truck bed and you won't have the front of the canoe sticking up so far in the air where it could hit low branches or bridges or anything.

Great knowledge and how to video on the hydro fluid but I will add that motor oil and hydronic oil are not supposed to be swapped. They have different chemical properties and can cause damage

I have a 2024 cheetah 2 any recommendations to make that seat softer

Nice day for fishing and thank you for the video sir 👍😎🇺🇸

This is my new favorite youtube video. Btw, what year was the garage door installed?

Thank You son!

Mark, what was the final outcome on the 5-1/2" pulley. Solve the clogging problem, cause any bearing failures?

Where did the 12oz per fork come from? My FSM says 6oz (5.2oz at oil change) per fork.

Great video, thanks!

😎💪

I dread doing the smaller front tires its always a NITE MARE for me!😫

Thank you for the video sir 👍😎🇺🇸

Very hard work and nice couple

Are you just walking around to random properties cutting up trees or are these jobs your were hired to do?

Great video thanks! Sorry about your camera

I tested a prototype 2024 BR900C it’s max is 302mph and I almost flipped my geo metro over with it

Great set up. I’m perusing something similar . Does your zero turn handle the weight towing, the front weights on mower and the second blower?

Very nice Ms Vickie and thank you for the video 👍😎🇺🇸

I’m afraid to take my carbs off on account of perhaps cracking the boots. My bike is at 1984 Nighthawk 750 S. Parts are scarce.

what size tire did you do - my cruiser has 15 and 16 in wheels... and apparently it doesn't do 15's? due to the top ring??? any way you figure to work around that?

Look up what shot peen is before you do this

Great job

I’m literally doing the same engine swap. I was fortunate enough to have a scag tiger cub given to me with a blown engine. I have the same Kohler engine but a 25hp. Watched you other video of doing the job. Hopefully will have it finished up by tomorrow. In hope of all of this, I’ll have my own mower again instead of borrowing one from friends and family. Now to figure out how you wired the starter solenoid, have a good idea based on your video. Just been better of if I had a picture. Oh well, I’ll figure it out.

My gravely dealer carries Skag and bob cat mowers Had my Gravly going on 10 years now

Everyone screws up at least once in their life. Love the demo on how NOT to maneuver a Gravely in a crowded garage. (Love the Harley, too.) My comment/question is why not use an oil extractor? I just got a manual pump-it-yourself version at Northern Tools for $20.

A true pro. Noticed the struggle with the roof protective film . My 10 x 12 will get here soon but the roof planks are undulated .Hopefully one of my sons will give me a hand . Thanks for posting.

Terrible video, no light

What makes this a Jumanji house?

Great video, i have same machine. It started last season 2023 steering levers where getting further apart. Then reverse was getting worse. I adjusted the rod on right side and was better forward but worse in reverse. Saw your video and had same problem. tightened two bolts readjusted the rod back to where it should be. THANK YOU!!!!!!!!!!!

Great job 👍

Thanks for your video, and most of all for the MLKJR quote

80mls of oil . mate u can destroy peoples mowers with this video. r u ok ?

I miss these videos! Nice work!

😎🇺🇸👍

Good job. I have the same Scag with a clamshell and I love it

Looks great!

What was wrong with the Kawasaki that was on the mower? I have a 20 hp Kawasaki that threw a rod through my engine block.

Nice work and thank you for the video sir 👍😎🇺🇸

❤👏